Pallet securing system
Stacks of corrugated board ready for dispatch can be secured with covering material for transport. Pallets, protective boards or protective sheets can be used for this purpose. After adding the covering material the stacks can be fed into the strapping and wrapping unit. MINDA supplies the necessary conveyor technology for these areas and acts as a general contractor so that there is only one contact partner for you. Furthermore, we realize the safe palletizing of your goods with our pallet loading station for single and double stacks .
Plastic chain conveyor for pallet securing system
Advantages:
- Flexible working widths and lengths for each strapping and wrapping unit adjusted to local conditions
- Transport of all formats
- Designed for the machine performance
- Smooth transport through frequency-controlled drives
- Reverse operation mode
- Low maintenance expenses
- High safety for the operating personnel
- Complete visualization and material flow tracking
Turntable
By means of turntables, directional changes of transport sections can be achieved which, for example, take structural conditions into account.
Right angle stations
Right angle stations are used in corrugated cardboard transport systems when the transport direction in the process is changed by 90° and thus the length-width-ratio is also changed.
Advantages:
- Both transport directions with plastic chain
- Large-scale support of goods
- Gentle transport of bottom sheets
- Suitable for all formats and qualities
- Compact and safe construction
Pallet loading station BOP
Pallet loading station for single stacks
The pallet loading station as single loading station is used to load a block for sheets as well as for finished goods. Block lengths and widths from 500 mm to 1,800 mm or from 500 mm to 2,100 mm can be palletized with a minimum stacking height of 400 mm. A maximum of 120 to 140 loads can be put on pallets per hour.
Thanks to its extremely compact design, a single loading station can be easily integrated into existing systems.
Single or double loading station
Single resp. double loading stations are used for the transport of sheets, when a large-size block of, for example, 2.4 x 5.0 m is to be positioned on pallets. Up to 100 blocks can be palletized per hour. It is, however, also possible to palletize two blocks of smaller sizes, e.g. 2.4 x 2.4 m or 1.6 x 1.8 m, of the same width in one cycle. Up to 200 blocks are palletized per hour. These models can be used for sheets as well as for finished goods.
Pallet loading station with divided walls
The walls and the pusher are separated and separately driven to allow loading of different block widths in one work cycle. For longer blocks, the walls and the pusher are displaced at the same time and only one block is placed on the pallet.
Empty pallet robot P-DROID
The empty pallet robot takes the empty pallets from the pallet stack and deposits them one after the other in the desired direction during pallet preparation. The pallets are pushed off by 90°. Depending on the requirements, a defined pallet pattern is created.
The pallet pusher laterally pushes the pallets under the pallet loading station, where the pallets can be positioned according to definition. The pallets can be taken or deposited in lengthwise and crosswise direction at high speed. Several types of empty pallets can be used in parallel.
In order to increase the performance, it is possible to take two pallets from the stack at the same time and to deposit them individually.
Pallet loading center installed in Austria
In a pallet loading station sheets as well as finished goods can be positioned on pallets. The protection sheet dispenser fully-automatically applies a bottom edge protection which is required for the strapping process. The empty pallet robot positions the empty pallets. Upon demand it is also possible to create pallet patterns in the feeding section. A capping material robot applies top pallets, panels and grids.
Finally the palletized material is automatically strapped and stretched.
Control
Complex control of individual intralogistics systems
There is a complex control process behind the flexibility and the size of these intralogistics processes. This process also includes software solutions optimally adjusted to the individual conditions.
They are based on MINDA MoveIT, the control and visualization system for intralogistics programmed by MINDA.
The system coodinates the control of transport sections, floor conveyors and packing devices according to the plans of the ERP system.
This superordinated control based on PC is further internally developed by experienced programmers.
MINDA MoveIT guarantees a fully-automatic operation in all transport sections. The transport operations are optimized so that all storing places are efficiently used.
In the discharge area behind the corrugator the system exactly defines how and in which order and sequence the corrugated cardboard stacks reach the intermediate storage and the converting machines with an optimal utilization of the transport capacity.
These calculations are effected in real time and are the condition for continuous new evaluations of the prioritites of the individual operations.
Complete transport operation
The converting machines are supplied in time with goods for conversion according to the definitions of the ERP systems. After the conversion, the corrugated cardboard stacks are discharged from the machines and fed to the pallet protection. (picture 2) Here the correct pallet type is automatically prepared and the data for the strapping are available. The secured goods reach the finished goods storage and are ready for despatch.
The system flexibly reacts to inputs by the operators. During the entire production process the products can always be identified.
A dynamic visualization of the processes provides the customer an overview of the complete production flow.
Further MINDA solutions for the corrugated board industry.
Machine feeding
Our services and fields:
Finished goods transport
Our services and fields: